“Quality and Service without Compromise”

Parts and fluids included in this package:
Tailored perfectly to each BMW engine, Genuine approved oil filters are made with synthetic fibres for even greater robustness. They are capable of meeting the demands of synthetic oils and high oil temperatures, with a large filtration area (up to 3,800 sq. cm) that removes great amounts of impurities such as engine sludge and deposits. Even the finest particles - 0.005 millimetres and smaller - are filtered out, leaving only the purest oil and thus being more environmentally friendly as they reduce fuel consumption. Genuine approved oil filters are outstanding in their seal quality which prevents impure oil from returning to the oil circuit and in addition protect the engine and extend its service life.
Work performed in this package:
Engine compartment.

• Engine oil is removed and replaced with new oil.
• Oil filter is removed and replaced with new filter.
• Service interval indicator is reset according to factory specifications.

Chassis area.
Brake pads:

• Check pad thickness with measuring gauge.
  If changing pads: clean brake pad take-ups. Brake discs: check surface and thickness. If changing pads at rear: check parking brake linings. Grease wheel centring mount on alloy wheels.

Parking brake:

• Check function, adjust as per instructions if necessary.

A motor oil service is performed by expert technicians at GISC  for optimal performance.

Tailored perfectly to each BMW engine, Genuine approved oil filters are made with synthetic fibres for even greater robustness. They are capable of meeting the demands of synthetic oils and high oil temperatures, with a large filtration area (up to 3,800 sq. cm) that removes great amounts of impurities such as engine sludge and deposits. Even the finest particles - 0.005 millimetres and smaller - are filtered out, leaving only the purest oil and thus being more environmentally friendly as they reduce fuel consumption. Genuine approved oil filters are outstanding in their seal quality which prevents impure oil from returning to the oil circuit and in addition protect the engine and extend its service life.

Did you know that checking the M3's engine valve clearances is vital in ensuring its longevity and ongoing performance? If these aren't checked and adjusted, there is a risk of accelerated component wear and possible engine damage, not to mention increased fuel consumption and a negative effect on your car's performance.

Not all independent specialist perform a check of the engine valve clearances as part of the Full Service Inspection - an important part of the BMW M3's service schedule. With GISC , you can be assured that this will be covered as part of any Inspection Service.

Parts included in this package:

This package includes wearing parts, materials and fluids that meet the strict BMW quality standards.

Work performed in this package:

Body/electrical equipment.

• Lighting system is checked.
• Instrument panel, dashboard illumination, and heater blower fan are checked.
• Horn, headlight flasher and hazard warning system are checked.
• Seat belts: condition of seat belt, function of automatic-locking retractor, belt lock and belt buckle.
• Battery: acid level and state-of-charge are checked and charged if required.**
• Microfilter or activated charcoal filter are replaced.**
• Change M-Mobility System sealant bottle after 3 years.
• Check entire body, except cavities, for corrosion.

Engine compartment.

• Test with diagnostic system is performed to determine if any faults had been automatically recorded by the vehicle.
• Motor oil and oil filter are removed and replaced with new oil and filter.
• Check valve clearance.
• Remove plugs and replace (petrol)
• Remove air filter and replace
• Remove pollen filter and replace
• Coolant levels are checked; when refilled, concentration of fluid is checked.
• At the corresponding interval coolant is changed (every four years at the latest), fluid is added as needed.**
• Service interval indicator is reset according to factory specifications.
• Fluid level and antifreeze additive in windscreen washer fluid reservoir are checked and topped up if needed.
• Steering fluid reservoir is checked and fluid is topped up if needed.
• At the corresponding interval brake fluid is replaced (every two years at the latest).**
• Spark plugs are replaced.
• Intake air cleaner element is replaced.

Chassis area.

• Overall thickness of front and rear disc brake pads is checked using a special tool. If replacement is necessary: surfaces are checked, brake pad contact points in callipers and brake shafts are cleaned. If replacement in rear is necessary: parking brake linings are checked. Wheel centring hubs on light-alloy wheels are greased.*
• Steering system is checked for play, leakage, damage and wear.
• Fluid change in rear differential.
• Oil change in manual gearbox.
• Undercarriage and body including all visible parts are checked for damage, leakage and corrosion.
• Brake system cables and connections are checked for leaks, damage and correct positioning.
• Functionality of parking brake is checked and adjusted where needed according to regulations.
• Tyre pressure is checked and adjusted where needed (including spare wheel), and external condition, tread depth and wear pattern are checked.

Final inspection.

• Road worthiness is checked, including brakes, steering/power steering, clutch, shock absorbers, control and warning lamps, Check Control (the system that monitors and displays information on the current condition of major functions such as doors, boot lid, lights, etc.)
• Complimentary valet included in this service

Full Service from £380.00

Prices shown are valid for all E46 M3 vehicles produced between February 2001 and August 2006. Specified services only. Prices include VAT, parts and labour.

**Additional costs may apply, for further details please contact GISC